Eaton Power Xpert XGIS Instruction Booklet Download Page 23

Page: 23 / 80

Instruction Booklet

IB022018EN

Effective July 2020

Instructions for the installation and

commissioning of Power Xpert

XGIS gas insulated switchgear

EATON

www.eaton.com

Figure 42. 1250 A cable connection CT mount.

Figure 43. 2500 A cable connection CT mount.

Figure 44.

Change spacer length to accommodate
various CT configurations

1250 A cable connection CT bracket.

Figure 45.

Change spacer length to accommodate
various CT configurations

2500 A cable connection CT bracket.

For more information about CT mounting and brackets, see section

5.13

, Installing current transformers.

Bus tie connections
XGIS sections can be configured with bus tie connections, so that

adjacent vertical section output bushings are directly connected

using SSIS bus. In that case, a different SF

tank is used, the output

bushings are mounted vertically in the tank bottom and connected to

bus joints connecting SSIS bus sections.

Summary of Contents for Power Xpert XGIS

















































































Search results

Summary of Contents for Power Xpert XGIS

Reviews:

Related manuals for Power Xpert XGIS

Brands by name

Popular brands

Eaton Power Xpert XGIS, Instruction Booklet

Search results

Summary of Contents for Power Xpert XGIS

Reviews:

Related manuals for Power Xpert XGIS

Brands by name

Popular brands