Eaton Power Xpert XGIS Instruction Booklet Download Page 25

Page: 25 / 80

Instruction Booklet

IB022018EN

Effective July 2020

Instructions for the installation and

commissioning of Power Xpert

XGIS gas insulated switchgear

EATON

www.eaton.com

Figure 49.

POWER XPERT XGIS
CABLE GROUNDING KIT
1250 A, ONE CABLE

NOTE: TEE CONNECTORS

NOT INCLUDED

XGIS cable grounding kit, one cable.

Figure 50.

POWER XPERT XGIS
CABLE GROUNDING KIT
1250 A, TWO CABLES

NOTE: TEE CONNECTORS

NOT INCLUDED

XGIS cable grounding kit, two cables.

Figure 51.

POWER XPERT XGIS
CABLE GROUNDING KIT
1250 A, THREE CABLES

NOTE: TEE CONNECTORS

NOT INCLUDED

XGIS cable grounding kit, three cables.

1.3.6 XGIS vertical section configurations

XGIS vertical sections come in five basic configurations. Options

are available to customize the equipment for each application. The

configurations are

•

Feeder/incoming

•

Bus tie

•

Bus sectionalizer

•

Disconnector

•

Cable connector

Summary of Contents for Power Xpert XGIS

















































































Search results

Summary of Contents for Power Xpert XGIS

Reviews:

Related manuals for Power Xpert XGIS

Brands by name

Popular brands

Eaton Power Xpert XGIS, Instruction Booklet

Search results

Summary of Contents for Power Xpert XGIS

Reviews:

Related manuals for Power Xpert XGIS

Brands by name

Popular brands