Eaton Paramount Enclosure Installation Manual Download Page 9

Page: 9 / 61

Figure

UNPACKING A FACTORY ASSEMBLED PTOC ENCLOSURE

1. Follow the unpacking and de-skidding instructions in the

“Standard Shipping Pallet”

section.

2. To allow the PTOC enclosure to be rolled off of the shipping pallet, the rear PTOC frame is attached in a

shipping position. The shipping position of the rear PTOC frame is approximately 1” higher than the normal

functional position of the frame.

3. Unlock and open the rear door. Locate the six screws that attach the rear PTOC frame to the enclosure frame.

Loosen the six screws to allow the rear frame to drop down to the functional position. Then re-tighten the

screws. See figure

PTOC frame

Screw

Move down

Pub Num: MN159002EN rev1.0

Paramount Enclosure
Installation Guide

Summary of Contents for Paramount Enclosure






























































Search results

Summary of Contents for Paramount Enclosure

Reviews:

Related manuals for Paramount Enclosure

Brands by name

Popular brands

Eaton Paramount Enclosure, Installation Manual

Search results

Summary of Contents for Paramount Enclosure

Reviews:

Related manuals for Paramount Enclosure

Brands by name

Popular brands