background image

PROFIBUS I/O Parameters

C441 PROFIBUS Module User Manual

MN042002EN—July 2015

www.eaton.com

25

PROFIBUS I/O Parameters

Cyclic IO Data for C441, C440, S611, S811+ and 
Stand-Alone I/O

There is a different Base Module that must be entered into 
the Base Module Slot in a PROFIBUS master’s software for 
each of the devices the C441 PROFIBUS modules interface 
to the PROFIBUS network. The Base modules are defined in 
the GSD file for the C441Q/S/QS/SS. The default Base 
module is the “IO StandAlone Base”. The other Base 
Modules are as follows:

C441 Motor Insight Base

C440 Overload Base

S611 Soft Starter Base

S811 Soft Starter Base

By default, the first 2 Data Exchange Module slots, from the 
GSD file contain the following:

Com Adapter Outputs_1

Control for the 2 outputs on the C441Q/S/QS/SS module

Com Adapter Inputs_1

Status of the 4 inputs on the C441Q/S/QS/SS module

These first 2 modules are used with all Base Modules. 
A third parameter may also be used with all of the Base 
modules: “Com Adapter Status”. Following the first 
2 parameters are the optional data shown below for each 
supported device, based on the Base Module used. If the 
IO StandAlone Base is used, only the COM Adapter 
Outputs_1, Com Adapter Inputs_1 and Com Adapter 
Status Data Exchange Parameters may be used.

Summary of Contents for C441 Series













































































Reviews: