manualshive.com logo in svg

E.T. Systems Drive 300, Installer'S Instructions, Page: 50 / 50

Share
Download
E.T. Systems Drive 300 Installer'S Instructions Download Page 50

50

WARRANTY:

1.  All goods manufactured by ET NICE (Pty) Ltd carry a 12 month factory warranty from date of invoice.

2.  All goods are warranted to be free of faulty components and manufacturing defects.

3.  Faulty goods will be repaired or replaced at the sole discretion of ET NICE (Pty) Ltd free of charge.

4.  This warranty is subject to the goods being returned to the premises of ET NICE (Pty) Ltd.

5.  The carriage of goods is for the customer’s account.

6.  This warranty is only valid if the correct installation and application of goods, as laid out in the applicable documentation accompanying 

said goods, is adhered to.

7.  All warranty claims must be accompanied by the original invoice.

8.  All claims made by the end user must be directed to their respective service provider/installer.

The following conditions will disqualify this product from the warranty as laid out above. These conditions are non- negotiable.

1.  Any unauthorized non-manufacturer modifications to the product or components thereof.

2.  Any modification to the installation methods described in the installation instructions.

3.  Any application or use of the product other than the intended use and application described in the product documentation.

The following items are not included in the warranty or they carry a special warranty condition of their own.

1.  The battery (Limited 6 month warranty)

2.  The motor brushes.

3.  Damage resultant of wind and other climatic influences such as lightning strikes.

4.  Damage due to high voltage surges on the household mains or short circuiting of the gates to the electric fencing.

5.  Damage due to infestation i.e. Ants nesting…

6.  Water damage. It is the responsibility of the installer to ensure the product is installed in a location that is protected from water ingress. 

The ingress protection rating is specified in the accompanying documentation. Housings that require that cable entries are made by the 

installer do not carry an ex-factory ingress protection rating as it is the responsibility of the installer to seal the cable entry points after 

installation of the cabling.

Summary of Contents for Drive 300



















































Reviews:

No comments