manualshive.com logo in svg

E.T. Systems Drive 300, Installer'S Instructions, Page: 26 / 50

Share
Download
E.T. Systems Drive 300 Installer'S Instructions Download Page 26

26

all

Receiver programming and setup.

Master erasing all users from the memory.

From Standby status

rdy

The gate can be in any position when performing this routine.

Action

Response

Description

Display

Buzzer

Gate

To enter the program 

menu. Press and hold the 

 button until buzzer 

beeps.

Display and buzzer 

confirms.

pr9

Scroll < or > to select the 

receiver setup option.

Display scrolls 

through options.

rc

With “rc” on the display, 

press and release 

.

Display changes to 

“Lrn” and buzzer 

beeps once

lrn

Scroll < or > to select the 

Erase remotes option.

Display scrolls 

through options.

era

With “ErA” on the display, 

press and release 

.

Display changes to 

“Adr” and buzzer 

beeps once.

adr

Scroll < or > to select the 

Erase ALL memory option.

Display scrolls 

through options.

all

With “ALL” on the display, 

press and hold 

.

“ALL” remains 

displayed

all

While still holding 

 

press the > button.

Buzzer begins 

beeping 

intermittently and 

“ALL” begins flashing.

NB! Releasing either 

button at this point 

will “Can” cancel the 

master erase.

all

Keep holding the buttons.

Display changes 

to “---” and buzzer 

silences. The master 

erase has begun.

---

Release the buttons.

Buzzer beeps  and 

“dnE” displays to 

indicate master erase 

is done.

dne

Press and release 

X 

to 

return to the main receiver 

programming menu.

Display changes to 

“ALL” and buzzer 

beeps.

all

x2

x1

x1

On/off...

x1

x1

Scroll left or right to next 

program option.

OR

rdy

EXIT back to standby 

status

Summary of Contents for Drive 300



















































Reviews:

No comments