manualshive.com logo in svg

E.T. Systems Drive 300, Installer'S Instructions, Page: 42 / 50

Share
Download
E.T. Systems Drive 300 Installer'S Instructions Download Page 42

42

Basic operating 

features

Auxiliary relay modes.

Receiver relay mode.  

User manual reference - 

Page 17

With Receiver relay mode selected, the auxiliary relay will operate in exactly the same way as a single channel receiver would, whenever a trans-

mitter button programmed into the “Relay” receiver function is pressed and released.

Latch mode.

The transmitter must be released and pressed again to toggle the relay each time.

Action

Response

Momentary relay trigger. 

Auxiliary relay 

switches on.

No buzzer tones.

Momentary relay trigger.

Auxiliary relay 

switches off.

No buzzer tones.

ON

Com

N/O

N/C

OFF

Com

N/O

N/C

One shot pulse mode.

The transmitter must be released and pressed again to reactivate the relay each time.

Action

Response

Momentary relay trigger. 

Auxiliary relay 

switches on.

No buzzer tones.

After relay timer has timed out.

Auxiliary relay 

switches off.

No buzzer tones.

ON

Com

N/O

N/C

0

3 sec.

OFF

Com

N/O

N/C

Summary of Contents for Drive 300



















































Reviews:

No comments