manualshive.com logo in svg

E.T. Systems Drive 300, Installer'S Instructions, Page: 43 / 50

Share
Download
E.T. Systems Drive 300 Installer'S Instructions Download Page 43

43

User manual reference - 

Page 18

Auxiliary relay modes.

Courtesy light mode.

Basic operating 

features

With courtesy light mode selected, the auxiliary light will switch on as the gate begins opening and remain on for 3 minutes after the gate has 

closed. 

The auxiliary relay can also be triggered to switch on without the gate opening by simply pressing and releasing any remote button programmed 

into the auxiliary relay function of the receiver. 

Below is an example of courtesy light mode when standard BT mode is active.

Action

Response

Momentary BT trigger.

Auxiliary relay 

activates.

No buzzer tone.

Gate begins 

opening.

Gate reaches open 

position.

Gate stops.

No buzzer tone.

Momentary BT trigger.

Gate begins 

closing.

No buzzer tone.

At full closed position.

Gate stops.

No buzzer tone.

Relay on timer 

begins counting 

down.

After relay on timer 

timeout.

Auxiliary relay 

deactivates.

No buzzer tone.

If any remote button programmed into the auxiliary relay function is pressed momentarily, the following will 

occur.

Auxiliary relay status

Action

Response

Momentary 

auxiliary relay 

trigger.

Auxiliary relay 

switches on for 

1 hour.

No buzzer tone.

Momentary 

auxiliary relay 

trigger.

Auxiliary relay 

switches off.

No buzzer tone.

ON

Com

N/O

N/C

3 Min.

0

0

0 sec.

c.

OFF

Com

N/O

N/C

OFF

Com

N/O

N/C

0

1 hour.

ON

Com

N/O

N/C

ON

Com

N/O

N/C

OFF

Com

N/O

N/C

Summary of Contents for Drive 300



















































Reviews:

No comments