manualshive.com logo in svg

E.T. Systems Drive 300, Installer'S Instructions, Page: 4 / 50

Share
Download
E.T. Systems Drive 300 Installer'S Instructions Download Page 4

4

5. 

It is highly recommended that a set of safety infra-red beams be used in conjunction with this product. The safety beams must be 

installed in such a way that the product is prevented from running when anything is in the path of the door or gate.

6. 

Over and above the recommendation to use safety infra-red beams with this product it is mandatory to install and use a safety 

beam set when using the automatic closing feature. It is recommended that a warning light be fitted to any automation system.

7. 

The emergency manual release instruction label must be installed on or adjacent to the emergency manual release mechanism.

After installation - It is the responsibility of the installer to ensure the users:

1. 

Is proficient in the use of the manual emergency release mechanism.

2. 

Is issued with the documentation accompanying this product.

3. 

Understands that the gate or door may not be operated out of clear sight.

4. 

Ensures that children are kept clear of the gate or door area at all times, and that children do not play with the remote transmitters 

or any fixed trigger switches linked to the system.

5. 

Is instructed not to attempt to repair or adjust the automation system and to be aware of the danger of continuing to use the 

automation system in an unsafe condition before a service provider attends to it.

6. 

Is proficient in testing the unit’s safety obstruction sensing system.

7. 

Is aware of what to check for with regards to wear and tear that may need to be attended to from time to time by the service 

provider.

8. 

Is aware that a fatigued battery may not be disposed of in the general refuse and must be handed in at a battery merchant for safe 

disposal. Before removing the battery from the system the household mains must be disconnected. In the case of the motor unit 

being removed and scrapped, the battery must be removed first.

Technical specifications.

Rated gate mass.

300kg

Maximum gate leaf length.

25m

Primary power supply to gate.

220 – 240Vac @ 50Hz – 60Hz 

(A low voltage plug-in transformer can be purchased and installed if required)

Peak power consumption at gate

18W

Electrical class.

Class 1 

Motor voltage.

24Vdc

Motor current limiting.

5A Starting / 3,5A Running

Rated duty cycle.

25% with 220Vac present (See determining your duty cycle on page 7)

Number of operations on battery reserve 

within 24 hours of power failure.

100 (Gate load and battery health dependent. Based on a gate opening of 4m)

Gate speed.

25m/min (Gate load and battery health dependent)

Rated Load.

300N Starting / 240N Running

Operating temperature range.

-10 to 50° C (14F to 122F)

Anti-crushing safety sensing.

Yes – Electronic gate profiling

Auxiliary supply output.

12Vdc @ 400mA

Built in battery charger.

Multiple stage auto-calibrating (350mA peak)

Receiver format.

ET BLU MIX ® Backward compatible with ET BLUE (Rolling code)

Receiver frequency.

433.92MHz

Receiver channels.

4CH (BT, PED, Aux relay, Holiday lock-out)

Receiver memory capacity.

32 users

All users can be allowed control of all channels.

Yes

Ingress protection.

IPX4

Summary of Contents for Drive 300



















































Reviews:

No comments