manualshive.com logo in svg

E.T. Systems Drive 300, Installer'S Instructions, Page: 27 / 50

Share
Download
E.T. Systems Drive 300 Installer'S Instructions Download Page 27

27

Receiver programming and setup.

Using the diagnostics feature.

dia

From Ready status

rdy

The gates can be in any position when performing this routine.

Action

Response

Description

Display

Buzzer

Gate

To enter the program 

menu. Press and hold 

 

until buzzer beeps.

Display and buzzer 

confirms.

pr9

Not appicable.

Use the 

<

 or 

>

 buttons and 

scroll until “rc” displays

rc

Not appicable.

With “rc” on the display, 

press and release 

.

Display changes to 

“Lrn” and buzzer 

beeps once

lrn

Not appicable.

Use the 

< 

or 

>

 buttons to 

select “diA”

Display changes with 

each button press.

dia

Not appicable.

With “diA” on the display, 

press and release 

.

Display changes to 

the signal strength 

indicator and buzzer 

beeps once

i

Not appicable.

In the case of any transmitter on the same 

frequency as the receiver, being active in the 

area, the signal strength guide will display 

how strong the incoming interfering signal is.

Weak signal

i

Not appicable.

Low signal.

ii

Not appicable.

Low/medium signal

iii

Not appicable.

Medium signal

iiii

Not appicable.

Medium/strong signal

iiiii

Not appicable.

Strong signal

iiiiii

Not appicable.

Press and release a 

remote transmitter button 

already learnt into the 

receiver memory.

Buzzer beeps once 

and user address 

display momentarily.

008

Not appicable.

Followed by the 

channel that button is 

learnt into.

bt

Not appicable.

Followed by the 

signal strength of the 

transmission.

iiiiii

Not appicable.

When done testing 

remotes, press and 

release 

X

 to return 

to the main receiver 

programming menu.

Display changes to 

“diA” and buzzer 

beeps once

dia

Not appicable.

Scroll 

< 

or 

> 

to next 

program option.

OR

EXIT back to 

Ready status

rdy

x2

x1

x1

x1

x1

Summary of Contents for Drive 300



















































Reviews:

No comments