manualshive.com logo in svg

E.T. Systems Drive 300, Installer'S Instructions, Page: 19 / 50

Share
Download
E.T. Systems Drive 300 Installer'S Instructions Download Page 19

19

Setting up the gate runtime. (Mandatory)

run

From Ready status

rdy

Before continuing with the runtime setup ensure the limit actuator has 

been installed correctly as per page 16 in this manual. Begin with the 

gate midway in its travel.

NB. To speed up the gate while running during this procedure, press and hold 

either the < or > buttons. 

Action

Response

Description

Display

Buzzer

Gate/s

To enter the program 

menu. Press and hold the 

 button until buzzer 

beeps.

Display and buzzer 

confirms.

pr9

Scroll < or > to select the 

runtime setup option.

Display scrolls 

through options.

run

Ensure gate is engaged 

midway and then press 

 

button.

Display prompts 

you to confirm gate 

closing direction. 

cl

dir

Confirm gate closing 

direction by pressing and 

releasing either the < or > 

button.

Gate closes slowly.

Display confirms.

Lft
r9t

When the closed position 

is reached and the closed 

limit is triggered. LED on.

Gate stops and starts 

opening.

lrn

Press and release the 

 

button to stop the gate 

at the required open 

position.

Gate stops opening. 

Display asks you to 

fine adjust the open 

position if required.

adj

Fine adjust the open 

position using the < or > 

buttons, if necessary.

Gate moves with 

each button press in 

either direction.

adj

When satisfied with the 

open position, press and 

release the 

 button to 

save that position.

Gate closes slowly.

Display and buzzer 

confirms.

lrn

When the closed position 

is reached and the closed 

limit is triggered. LED on.

Gate stops. Display 

and buzzer warn the 

profiling is about to 

begin.

pro

Once warning tone has 

stopped.

Gate begins running 

open at full speed.

Display confirms.

pro

When the previously 

programmed open 

position is reached.

Gate stops and 

begins closing again 

at full speed. Display 

confirms.

pro

When the closed position 

is reached and the closed 

limit is triggered. LED on.

Gate stops. Display 

and buzzer confirms.

dne

x2

x1

STOP

x1

x1

On/off...

On/off...

x2

Scroll left or right to next 

program option.

OR

rdy

EXIT back to ready 

status

Summary of Contents for Drive 300



















































Reviews:

No comments