manualshive.com logo in svg

E.T. Systems Drive 300, Installer'S Instructions, Page: 23 / 50

Share
Download
E.T. Systems Drive 300 Installer'S Instructions Download Page 23

23

Receiver programming and setup.

Setting up a new user.

lrn

From Ready status

rdy

The gate can be in any position when performing this routine.

Please note that if an ET BLU MIX © transmitter is being used and 

not all of the buttons have been set to the same format, then the 

receiver will allocate 2 user addresses for the various buttons. 1 for 

the buttons set to ET BLU MIX© and 1 for the buttons set to ET BLUE.

Action

Response

Description

Display

Buzzer

Gate

To enter the program 

menu. Press and hold the 

 button until buzzer 

beeps.

Display and buzzer 

confirms.

pr9

Scroll < or > to select the 

receiver setup option.

Display scrolls 

through options.

rc

With “rc” on the display, 

press and release 

.

Display shows current 

option status.

lrn

With “Lrn” on the display, 

press and release 

.

Display prompts you 

to select a function.

bt

Scroll < or > to the required 

receiver function/channel 

option.

NB! Corresponding 4 

function learn option 

is explained in the next 

instruction table on the 

next page.

Display changes 

respectively.

bt

ped

rly

hol

cor

Press and hold required 

button on the remote 

transmitter.

While still transmitting with 

the remote button, press 

and release 

.

After the 

 button 

has been released, 

the user address 

for that transmitter 

displays and the 

buzzer beeps 

confirms.

001

Release the button on the 

remote transmitter.

Repeat the last 4 steps here for additional users or functions, or exit back one level in the receiver setup menu for other receiver setup options.

x2

x1

x2

Scroll left or right to next 

program option.

OR

rdy

EXIT back to standby 

status

Summary of Contents for Drive 300



















































Reviews:

No comments