background image

2

E-flite LR-1A Pogo 15e ARF Assembly Manual

Introduction

Congratulations on buying the LR-1A Pogo airplane. 

You have purchased what is arguably one of the most 

fun airplanes in the marketplace today. Originally 

designed as a fast sport flyer to bring an adrenaline 

rush to the mid to advanced pilots, the project quickly 

advanced to an even greater purpose. Working with 

legendary designer Jerry Small we developed the 

airplane into the standard for the upcoming Electric 

Formula One racing class from the NMPRA (National 

Miniature Pylon Racing Association).

Jerry designed a unique cowl system that includes all 

the graceful curves of the front of the fuselage into one 

piece that stretches back to the mid canopy point. This 

allows for very easy maintenance, easy mounting of 

equipment, and great cooling for the EP power system. 

We also elected to use mini servos throughout to save 

weight and expense; for the same reasons there is only 

one aileron servo.

Power for your airplane can be anything from our 

Power 15 motor on a 3S setup and a 10 x 10E prop 

(prop clearance limits anything longer) to a full blown 

race setup with our new Power 25 1250Kv on 4S and 

an 8 x 8E prop turning about 15,000 rpm. The sport 

setup will put you in the 80 mph range while the race 

setup has been clocked at about 115 mph. 

The airplane is a smooth flyer and goes exactly where 

you point it. Make sure all your friends pick up one of 

these kits then challenge each other to some impromptu 

racing for bragging rights at your local field. You’ll 

have a blast!

Product Support

For technical assistance with this product, please 

contact the appropriate Horizon Product Support 

office. See page 36.

Notice

All instructions, warranties and other collateral 

documents are subject to change at the sole discretion 

of Horizon Hobby, Inc. For up to date product 

literature, visit http://www.horizonhobby.com.

Meaning of Special Language

WARNING: Procedures, which if not properly 

followed, create the likely probability of physical 

property damage AND may lead to a dangerous 

condition or cause death or serious injury to the user, 

OR procedures, which if not followed, create the high 

probability of superficial injury. 

 

WARNING: Read the ENTIRE instruction manual 

to become familiar with the features of the product 

before operating. Failure to operate the product 

correctly can result in damage to the product, personal 

property and cause serious injury. 

This is a sophisticated hobby product and NOT a toy. 

It must be operated with caution and common sense 

and requires some basic mechanical ability. Failure 

to operate this Product in a safe and responsible 

manner could result in injury or damage to the 

product or other property. This product is not intended 

for use by children without direct adult supervision. 

Do not attempt disassemble, use with incompatible 

components or augment product in any way without 

the approval of Horizon Hobby, Inc. This manual 

contains instructions for safety, operation and 

maintenance. It is essential to read and follow all 

the instructions and warnings in the manual, prior to 

assembly, setup or use, in order to operate correctly 

and avoid damage or serious injury.

Table of Contents

Notice ................................................................... 2

Meaning of Special Language ................................. 2

Introduction ........................................................... 2

Product Support ..................................................... 2

Specifications ......................................................... 3

Contents of Kit/Parts Layout .................................... 3

Warnings .............................................................. 3

Important Information Regarding  

Warranty Information ........................................ 4

Using the Manual ................................................... 4

Covering Colors ..................................................... 4

Recommended Radio Equipment ............................. 4

Required Tools and Adhesives ................................. 4

Recommended Sport Setup ..................................... 4

Recommended Racing Setup ................................... 5

Optional Accessories .............................................. 5

Hinging the Ailerons .............................................. 5

Joining the Wing Panels ......................................... 7

Installing the Aileron Servo ..................................... 8

Hinging the Elevators ........................................... 12

Tail Wheel Installation and Hinging the Rudder ...... 14

Motor and Speed Control Installation .................... 17

Cowling Installation .............................................. 19

Propeller and Spinner Installation .......................... 21

Wing and Stabilizer Installation ............................ 21

Rudder and Fin Installation ................................... 23

Servo and Receiver Installation .............................. 25

Rudder and Elevator Linkage Connections .............. 26

Battery and Wing Installation ................................ 30

Landing Gear Installation ...................................... 30

Center of Gravity ................................................. 32

Control Throws..................................................... 33

Preflight ............................................................... 34

Flying Your LR-1A Pogo 15e ................................. 34

Range Test Your Radio .......................................... 35

Safety Do’s and Don’ts for Pilots ............................ 35

Daily Flight Checks ............................................... 35

Warranty and Repair Policy .................................. 36

Warranty Services ................................................ 36

Compliance Information for the European Union .... 37

2010 Official Academy of  

Model Aeronautics Safety Code ....................... 38

Summary of Contents for LR-1A Pogo 15e









































Reviews: