Fisher-Price BARBIE BEACH RANGER 78477 Owner'S Manual & Assembly Instructions Download

Page: 1 / 36

Owner’s Manual

with Assembly Instructions

Please read this manual and save it with your original sales receipt.

For Model 78477

Tools needed for assembly: Phillips Screwdriver, Hammer, and Safety Scissors.

Use only with Power Wheels

Type H 6 Volt (9.5 Amp./hr. - included or 12 Amp./hr. - not included) Batteries,

Power Wheels

30 Amp Fuses (included) and Power Wheels

Type H 12 Volt Charger (included).

Requires four LR6 "AA" alkaline batteries (not included) for Lights and Siren.

CAUTION

ELECTRIC TOY: Not recommended for children under 3 years of age.

As with all electric products, precautions should be observed during

handling and use to prevent electric shock.

Product features and decoration may vary from the picture above.

™

Summary of Contents for BARBIE BEACH RANGER 78477





































Search results

Summary of Contents for BARBIE BEACH RANGER 78477

Reviews:

Related manuals for BARBIE BEACH RANGER 78477

Brands by name

Popular brands

Fisher-Price BARBIE BEACH RANGER 78477, Owner'S Manual & Assembly Instructions

Search results

Summary of Contents for BARBIE BEACH RANGER 78477

Reviews:

Related manuals for BARBIE BEACH RANGER 78477

Brands by name

Popular brands