E-FLITE Blade CP Manual Download Page 28

Page: 28 / 68

• Carefully pass each of the rods through the holes in the attachments on the landing skids and into the

channels on the base. The rods will pass through the front holes of the forward attachments, and the

back holes of the rear attachments. You may find it necessary apply some light pressure to the rods,

base and landing skids when installing all four rods in the base. This is typical, however, take care to

not pull the landing struts out of their mounts in the frame and to not damage any of the parts.
Once all four rods are installed, note that the landing skids may be pulled slightly inward under their

pressure. This is also typical as the pressure helps to keep the training gear in place.

• Install one plastic ball on the exposed end of each rod. Then, slide one tubing keeper over the end

of each rod to prevent the ball from sliding off. Adjust the position of the tubing keepers that were

factory-installed on each rod until they are just touching each plastic ball. The tubing keepers should

then be positioned so that the ball can spin freely on the rod, without too much movement side-to-side

between the keepers.
Your Blade CP+ is now ready for flight with the training gear installed.

Summary of Contents for Blade CP





































































Search results

Summary of Contents for Blade CP

Reviews:

Related manuals for Blade CP

Brands by name

Popular brands

E-FLITE Blade CP, Manual

Search results

Summary of Contents for Blade CP

Reviews:

Related manuals for Blade CP

Brands by name

Popular brands