E-FLITE Blade CP Manual Download Page 43 | Manualshive

Page: 43 / 68

background image

43

Flybar Paddle Tracking Adjustment

While main blade tracking is a critical element of flight performance, proper flybar paddle tracking

and positioning is also important in maintaining proper control response and vibration-free operation.
For checking flybar paddle tracking, positioning and making adjustments, please read the following

tips:

• First, be certain that both flybar paddles are equally spaced from the ends of the paddle control frame.
• Next, be certain that both flybar paddles are parallel to the paddle control frame.
• If you have made certain that both flybar paddles are parallel to the paddle control frame, they should

now be parallel to one another. If they are not, take your time making adjustments in order to ensure

that both flybar paddles are positioned parallel to one another and the paddle control frame.

• Once you have positioned the flybar paddles correctly following the steps above, be certain they are

firmly secured using the included screws, washers and hex nuts.

«
...
41
42
43
44
45
...
»

Summary of Contents for Blade CP





































































Reviews:

No comments

Related manuals for Blade CP

Brand: Gogen Pages: 40

100 English-Chinese Words Book

Brand: LeapFrog Pages: 10

Brand: Power Wheels Pages: 32

Super Chief Xtra DCS100

Brand: Digitrax Pages: 119

Brand: Bigben Pages: 52

80-072300 - Little Einsteins Learn

Brand: VTech Pages: 14

Brand: Maison Battat Pages: 2

Brand: LEGO Pages: 16

Brand: Betzold Pages: 6

Brand: Faller Pages: 8

Brand: Faller Pages: 8

V.Smile: The Batman - Gotham City Rescue

Brand: VTech Pages: 20

Brand: MGA Entertainment Pages: 4

Mi Truck Builder MTJM01IQI

Brand: Xiaomi Pages: 2

Brand: BUSCH Pages: 2

Brand: Playskool Pages: 2

Brand: marklin Pages: 40

Brand: Faller Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands