E-FLITE Blade CP Manual Download Page 57 | Manualshive

Page: 57 / 68

background image

57

To the bottom of the battery/lower frame support rods, just below the main gear and behind the

battery support/mount. Use some small strips of foam mounting tape on the rods, and a long cable/

zip tie wrap (included in the “Mounting Accessories & Wrench” package), to secure the ESC in this

location. Be sure to also secure the receiver and battery power leads away from the gears and any

other moving parts. Then, depending on the length of the motor leads, it may also be necessary to

make up some short motor wire lead extensions (using approximately 1.5”–2.0” of wire and the

connectors included with the ESC) to connect the motor to the ESC.

• After securing the ESC in its mounting position, connect the motor wire leads to the connectors on the

ESC. The order of the wire leads in the connectors is not too important at this time, as any two of them

can be reversed if the motor does not spin in the proper direction after testing its operation.

«
...
55
56
57
58
59
...
»

Summary of Contents for Blade CP





































































Reviews:

No comments

Related manuals for Blade CP

Brand: Uhlenbrock Elektronik Pages: 34

Brand: ubisoft Pages: 21

Brand: Fisher-Price Pages: 8

Brand: LEGO Pages: 36

Deere CONSTRUCTION LOADER

Brand: Peg-Perego Pages: 52

Touch & Learn Activity Desk Deluxe

Brand: VTech Pages: 10

BLACK FOREST MILL

Brand: Faller Pages: 8

Brand: Kalee Pages: 6

Spitfire F.Mk.22/24

Brand: Eduard Pages: 5

Mighty Mini P-51B

Brand: MiniacRC Pages: 51

Brand: Volvo Pages: 10

1/48 KITTY HAWK KH80144 kit

Brand: Eduard Pages: 6

Leaping Letters

Brand: LeapFrog Pages: 2

Brand: Hot Wheels Pages: 4

Brand: LGB Pages: 14

Brand: Herr Pages: 16

Pelican Aileron Wing

Brand: CRASHTESTHOBBY.COM Pages: 7

LASER Sailing Boat & trailer

Brand: REVELL Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands