E-FLITE Blade CP Manual Download Page 37 | Manualshive

Page: 37 / 68

background image

37

Normal and Idle Up Flight Modes

The 6-channel FM transmitter included with your Blade CP+ features servo reversing and CCPM

mixing, as well as an “Idle Up” flight mode switch. This switch allows the pilot to toggle between

“normal” and “stunt” (aerobatic) flight modes during flight.

With the switch toggled toward the rear of the transmitter, the Blade CP+ will be flying in “normal

mode.” In this flight mode, the throttle curve is linear from 0% to 100%, with a pitch range of 0

degrees to +10 degrees. (See Page 40 for additional data and graphics relating to the throttle and

pitch curves preset for your Blade CP+.) This is the preferred flight mode for general hovering and

gentle forward flight.

Idle Up Switch

«
...
35
36
37
38
39
...
»

Summary of Contents for Blade CP





































































Reviews:

No comments

Related manuals for Blade CP

Brand: Quest Engineering Pages: 2

Brand: Old School Model Works Pages: 18

Brand: LEGO Pages: 64

Brand: Eduard Pages: 4

Brand: H-KING Pages: 13

Brand: Bengtson Company Pages: 7

Brand: J-Power Group Pages: 24

Brand: LEGO Pages: 72

Thunderbolt Strike Roller Coaster

Brand: K'Nex Pages: 44

75005 Pocket Poker

Brand: Radica Games Pages: 2

Brand: Jamara Pages: 20

Brand: Madcow Rocketry Pages: 3

Fuzzikins Dozy Dogs

Brand: PlayMonster Pages: 4

Brand: marklin Pages: 20

Brand: Trix Pages: 32

RAILKING GALLOPING GOOSE

Brand: Rail King Pages: 32

Volkswagen Beetle LED Lighting Kit

Brand: LIGHT MY BRICKS Pages: 15

Brand: Fisher-Price Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands