E-FLITE Blade CP Manual Download Page 19 | Manualshive

Page: 19 / 68

background image

19

Position the helicopter to view it from the left or right side. Move the left-hand stick up and down to

check the collective pitch control. When the stick is pushed up, the swashplate should lower, increasing

the pitch of the main blades.

With the stick pulled back down, the swashplate should raise, decreasing the pitch of the main blades.

«
...
17
18
19
20
21
...
»

Summary of Contents for Blade CP





































































Reviews:

No comments

Related manuals for Blade CP

Strike Eagle G1670B Cargo Plane

Brand: Laser Pegs Pages: 8

Brand: Laser Pegs Pages: 2

Call of Duty Legends: Winter Heroes

Brand: Mega Construx Pages: 2

Brand: Lionel Pages: 24

Triple-the-Fun Art Studio

Brand: Crayola Pages: 3

Minions Shark Bait

Brand: Mega Bloks Pages: 20

Brand: Knights of Dice Pages: 7

Brand: Viessmann Pages: 4

Brand: Gold Wing Pages: 45

Batman Power Wing Laptop

Brand: Oregon Scientific Pages: 24

Brand: Black Horse Model Pages: 30

wonder makers GGV82

Brand: Fisher-Price Pages: 32

Brand: Funkey Pages: 6

Brand: Eduard Pages: 8

Krupp Protze Kfz.70 & 3.7-cm-pak

Brand: REVELL Pages: 8

SUPER MARIO BROS.U LAYER CAKE DESERT

Brand: K'Nex Pages: 20

Brand: CARAMBA Pages: 6

Brand: Black Horce Model Pages: 38

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands