E-FLITE Blade CP Manual Download Page 39

Page: 39 / 68

Pitch Curve Adjustments

The pitch curves have already been factory set in the transmitter for both Normal and Idle Up/Stunt

flight modes. These curves have been tested and optimized for the best overall performance in either

flight mode.
Although the curves have already been factory set, minor changes to the pitch curves can also be

made by adjusting the Pitch Control Links. Lengthening both Pitch Control Links by equal amounts will

increase the pitch of both blades for a given throttle/collective stick position. Shortening both Pitch

Control Links by equal amounts will decrease the pitch of both blades for a given throttle/collective

stick position.

In general, we would recommend that you adjust the Pitch Control Links so that the blades are at 0

degrees of pitch when in the Idle Up/Stunt flight mode with the throttle/collective stick in the middle

position. This will help to ensure that you have an equal amount of positive and negative pitch travel

when in the Idle Up/Stunt flight mode, and that your curves more closely match those shown in the

“Programmed Throttle and Pitch Curves” section of this manual (page 40).

Pitch Control Link

Summary of Contents for Blade CP





































































Search results

Summary of Contents for Blade CP

Reviews:

Related manuals for Blade CP

Brands by name

Popular brands

E-FLITE Blade CP, Manual

Search results

Summary of Contents for Blade CP

Reviews:

Related manuals for Blade CP

Brands by name

Popular brands