E-FLITE Blade CP Manual Download Page 47 | Manualshive

Page: 47 / 68

background image

47

Note: The following steps outline the installation and setup of the G90 gyro, but can also be used

as reference for many other heading lock type gyros. However, we do recommend that you review

the manual included with your chosen gyro first before proceeding with installation and setup of the

gyro in your Blade CP+.

• Install the gyro using its included foam mounting tape (or the foam mounting tape found in the Blade

CP+’s included “Mounting Accessories & Wrench” package) on the gyro mounting plate found

just behind the rear servos. Be sure to orient the gyro so that you can easily access the gain setting

adjustment pot and any necessary reversing or other setting switches.

Note: It is extremely important to ensure that the gyro is mounted securely so that it will not come

loose in flight. Also, be sure that the gyro case does not come in contact with the servos or any

other parts of the helicopter.

«
...
45
46
47
48
49
...
»

Summary of Contents for Blade CP





































































Reviews:

No comments

Related manuals for Blade CP

Traffic Light-Grand

Brand: Jamara Pages: 4

Mercedes-Benz Arocs

Brand: Jamara Pages: 4

Mercedes-AMG GT

Brand: Jamara Pages: 8

Liebherr 2,4 GHz

Brand: Jamara Pages: 8

Brand: Jamara Pages: 20

Beaver DHC 2 V2

Brand: Jamara Pages: 24

Brand: Jamara Pages: 16

Brand: Jamara Pages: 8

Brand: Laser Pegs Pages: 6

Brand: Laser Pegs Pages: 4

Brand: Laser Pegs Pages: 3

Brand: Laser Pegs Pages: 17

Assault Helicopter C1200

Brand: Laser Pegs Pages: 3

ALL TERRAIN ROVER ZD 110B

Brand: Laser Pegs Pages: 16

Brand: Laser Pegs Pages: 2

National Geographic Oceans

Brand: Laser Pegs Pages: 2

Zlin Z-37A Cmelak

Brand: KOR MODEL Pages: 21

Brand: Fisher-Price Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands