manualshive.com logo in svg

Aeronaut Twinspeedy, Manual, Page: 1 / 5

Share
Download
Aeronaut Twinspeedy Manual Download Page 1

                                                                                                                                       Twinspeedy / Sailspeedy

 

 
Sailspeedy / Twinspeedy instructions

 

1 

Building instructions 
 
Twinspeedy 

Order No. 1319/01

 

 
Sailspeedy 

Order No. 1319/00 

 

 
 
“aero-naut” Modellbau 
Stuttgarterstr. 18-22   

                        

D-72766 Reutlingen   
Germany 

                                

http://www.aero-naut.de

 

 

 

 

 
This  model  is  of  very  simple  construction,  and  can  be  built  even  by  modellers  with  little  prior 
experience. All the parts contained in the kit are numbered, and the numbers are included in the text, 
the stage photos and the parts list. It is important to complete the model in the sequence described in 
these instructions, and to allow all glued joints to harden completely at the end of each stage before 
resuming  construction.  We  at  “aero-naut”  are  unable  to  monitor  the  methods  you  use  to  build  the 
model,  and  for  this  reason  “aero-naut”  accepts  no  liability  for  damage  or  injury  caused  during 
construction or operation of this model. 
 
Flying this model successfully requires a basic knowledge of model flight. If you are a beginner please 
ask an experienced model pilot to help you during the initial stages of learning to fly. 
Use 5-minute epoxy for all joints. 

 

Extra items required to complete the model 

 

1 

RC (radio control) system with V-tail mixer 

4 

9 g servos 

1 

Receiver battery 

1 

Clear adhesive tape, 10 - 20 mm wide 

1 

5-minute epoxy (two-pack resin adhesive) 

1 

Speed controller (for Twinspeedy only) 

2 

Race 400 6V motors, Order No. 7000/42, or Speed 400 6V (for Twinspeedy only) 

2 

Propellers (for Twinspeedy only), Order No. 7249/08 

1 

6-cell sub-C flight battery or 7-cell 4/5 sub-C flight battery (for Twinspeedy only)  

 
Translation for following pictures: 
 
6                 Servokabel 

Servo lead 

9 

Schnitt 

Cut 

14 

Kohlefaserrohr 

Carbon fibre tube 

 

Servoschacht 

Servo well 

 

Tragflaeche 

Wing 

 

Schnitt 

Cut 

 

Querruder 

Aileron 

 

Schlitz 

Slot 

 

Schnitt 

Cut 

18 

Spinner cap 

Summary of Contents for Twinspeedy






Reviews:

No comments