E-FLITE Blade CP Manual Download Page 1 | Manualshive

Page: 1 / 68

background image

Specifications

Length ............................................................................................................... 20.7 in (526mm)
Height .................................................................................................................. 7.1 in (180mm)
Main Rotor Diameter .......................................................................................... 20.8 in (528mm)
Tail Rotor Diameter ................................................................................................ 5.8 in (148mm)
Weight with Battery ...............................................................................................10.5 oz (298 g)
Main Motor ............................................................................................................ 370 (installed)
Tail Motor .............................................................................................................. N30 (installed)
Battery .....................................................................................3S 11.1V 800mAh Li-Po (included)
Charger .............................................................................. DC Li-Po balancing charger (included)
Transmitter.............................................................................. FM 6-channel with CCPM (included)
On-Board Electronics ......................... FM 6-channel receiver plus 3-in-1 mixer/ESC/gyro (installed)
Servos .................................................................................. 7.5-gram S75 Sub-Micro (3 installed)

1
2
3
...
»

Summary of Contents for Blade CP





































































Reviews:

No comments

Related manuals for Blade CP

SET OF FUNFAIR CARAVANS II

Brand: Faller Pages: 4

HALF-TIMBERED HOUSE

Brand: Faller Pages: 4

Brand: Faller Pages: 4

Brand: marklin Pages: 24

Sd.Kfz.251/1 Ausf.B

Brand: REVELL Pages: 7

Techno Tiles TT Castle

Brand: The Learning Journey Pages: 386

L5198 Bubble Mower

Brand: Fisher-Price Pages: 28

Minions Shark Bait

Brand: Mega Bloks Pages: 20

Brand: Trix Pages: 40

He 219 exterior

Brand: Eduard Pages: 2

SPEED MASTER TG511

Brand: THINK GIZMOS Pages: 6

Brand: BearCreeks Pages: 19

Brand: A4 Pages: 20

SH-3 Sea King interior

Brand: Eduard Pages: 2

Brand: INTERACTIVE TOY CONCEPTS Pages: 2

POST INN 232536

Brand: Faller Pages: 4

Brand: marklin Pages: 28

Brand: Tower Hobbies Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands