Dynapac ICA362 Instruction Manual Download Page 8

Page: 8 / 121

2000h-

Maintenance

ICA362-4EN3.pdf

2012-06-12

Maintenance - 250h ............................................................................................................... 89

Rear axle differential - Check oil level....................................................... 89

Rear axle planetary gears - Check oil level............................................... 90

Drum gearbox - Checking the oil level ...................................................... 90

Drum cartridge - Checking the oil level ..................................................... 91

Drum cartridge - Cleaning the ventilation screw ....................................... 92

Radiator - Check/Cleaning ........................................................................ 92

Bolted joints - Checking tightening torque................................................. 92

Rubber elements and fastening screws - Check....................................... 93

Battery - Check electrolyte level................................................................ 93

Battery cell ................................................................................................ 94

Air conditioning (Optional)
- Inspection................................................................................................ 94

Maintenance - 500h ............................................................................................................... 95

Replacing the fuel filter.............................................................................. 95

Controls and moving joints - Lubrication ................................................... 96

Fuel pre-filter - Cleaning............................................................................ 96

Diesel engine - Oil and Filter change ........................................................ 97

Steering chain and seat bearing - Lubrication........................................... 97

Seat bearing - Lubrication ......................................................................... 98

Maintenance - 1000h ............................................................................................................. 99

Hydraulic filter - Replacement ................................................................... 99

Hydraulic reservoir - Draining.................................................................. 100

Fuel tank - Drainage................................................................................ 101

Rear axle differential - Oil change........................................................... 101

Rear axle's planetary gears - Draining the oil ......................................... 102

Rear axle's planetary gears - Oil change - Oil filling ............................... 103

Air conditioning (Optional)
Fresh air filter - Change .......................................................................... 103

Maintenance - 2000h ........................................................................................................... 105

Summary of Contents for ICA362


























































































































Search results

Summary of Contents for ICA362

Reviews:

Related manuals for ICA362

Brands by name

Popular brands

Dynapac ICA362, Instruction Manual

Search results

Summary of Contents for ICA362

Reviews:

Related manuals for ICA362

Brands by name

Popular brands