Dynapac ICA362 Instruction Manual Download Page 97

Page: 97 / 121

Maintenance - 50h

ICA362-4EN3.pdf

2012-06-12

Fig. Cab
1. Condensor element

Where cooling capacity is markedly reduced, clean the
condensor element (1) located on the rear edge of the
cab. Also clean the cooling unit in the cab. See under
the heading 2000 hours, automatic climate control -
overhaul.

Strike-off blade (Optional)
- Lubrication

Fig. Strike-off blade
1. Lubrication nipples

Always lower the blade to the ground before
leaving or parking the roller.

Make sure that nobody is in the way when
operating the blade.

Wipe the nipples clean from grease and dirt, three on
each side of the machine.

Grease each nipple (1) with four strokes of the grease
gun. Ensure that grease penetrates the bearings.

Summary of Contents for ICA362


























































































































Search results

Summary of Contents for ICA362

Reviews:

Related manuals for ICA362

Brands by name

Popular brands

Dynapac ICA362, Instruction Manual

Search results

Summary of Contents for ICA362

Reviews:

Related manuals for ICA362

Brands by name

Popular brands