manualshive.com logo in svg

DuraTech Industries HAYBUSTER CMF-590, Operating Instructions And Parts Reference, Page: 6 / 110

Share
Download
DuraTech Industries HAYBUSTER CMF-590 Operating Instructions And Parts Reference Download Page 6

ii

C M F - 5 9 0                                 T A B L E   O F   C O N T E N T S

Purpose

The purpose of this owner’s manual is to explain maintenance requirements and 

routine adjustments for the most efficient operation of your CMF-590.  There is 

also a trouble shooting section that may help in case of problems in the field.  Any 

information not covered in this manual may be obtained from your dealer.

Special Note:  When reference is made as to front, rear, right hand or left 

hand of this machine, the reference is always made from standing at the rear 

end of the machine and looking towards the hitch.  Always use serial number 

and model number when referring to parts or problems.  Please obtain your 

serial number and write it below for your future reference.

MODEL:  CMF-590 VERTICAL MIXER  SERIAL NO__________________

F O R E W O R D

How to use this manual

Manual organization

This manual is organized into the following parts:

•

  Part 1: Operating Manual explains how to set up, use and maintain the CMF-590 VERTICAL MIXER.

 

 

1. 

Section  1: Safety 

 

 

2. 

Section  2: Dealer Preparation 

 

 

3. 

Section  3: Operation 

 

 

4. 

Section  4: Lubrication 

 

 

5. 

Section  5: Troubleshooting 

 

 

6. 

Section  6: Options 

 

 

7. 

Section  7: Maintenance 

•

  Part 2:  Parts Reference contains diagrams of each assembly, with the part number of each part.  A key on 

the facing page contains a description of the part and the quantity used.  

 

  1. The 

parts reference section can be found towards the back of this manual behind  

 

     Appendix B.

Summary of Contents for HAYBUSTER CMF-590















































































































Reviews:

No comments