manualshive.com logo in svg

DuraTech Industries HAYBUSTER CMF-590, Operating Instructions And Parts Reference, Page: 5 / 110

Share
Download
DuraTech Industries HAYBUSTER CMF-590 Operating Instructions And Parts Reference Download Page 5

i

C M F - 5 9 0                                 T A B L E   O F   C O N T E N T S

F O R E W O R D

Foreword 

All personnel must read and understand the following sections before operating the 

CMF-590 VERTICAL MIXER.

Appropriate use of unit\Introduction

Your model CMF-590 is designed to cut, mix and distribute feed rations including 

baled forage.  It is designed for all bale sizes and ration moisture contents.

To avoid possible damage to the machine and risk of injury to the operator, 

consult with a DuraTech Industries International, Inc.  

(DuraTech Industries) representative before attempting to mix and 

distribute materials other than livestock forage.

The CMF-590 is used to mix hay and forage with grain and other supplements to 

feed livestock.  The front conveyor with optional left, right or tandem discharge 

makes distribution of forage mix easier.

Statement of Misuse

This vertical mixer is not to be used for any purpose other than for which it is 

intended as explained in the operator’s manual, advertising material and other 

pertinent written material prepared by DuraTech Industries.  Any machine subject to 

misuse may cause personal injury or death, and void manufactures warranty.

Summary of Contents for HAYBUSTER CMF-590















































































































Reviews:

No comments