manualshive.com logo in svg

DuraTech Industries HAYBUSTER CMF-590, Operating Instructions And Parts Reference, Page: 33 / 110

Share
Download
DuraTech Industries HAYBUSTER CMF-590 Operating Instructions And Parts Reference Download Page 33

23

  C M F - 5 9 0    

O P E R A T I N G   I N S T R U C T I O N S

3.10 Removing the CMF-590 from storage

To remove the CMF-590 from storage, perform the following steps:

1.  Remove all protective coverings.

2.  Remove blockings from under the CMF-590.  Check tire pressure.

3.  Lubricate machine in accordance with lubrication instructions found in this manual.

4.  Check the conveyor chain tension.

5.  Check all hydraulic hoses for deterioration and, if necessary, replace.  Tighten any loose bolts, nuts and 

hydraulic fittings.

6.  Follow pre-starting inspection instructions.

3.11   Normal shut-down procedure

Warning: 

  For your safety and the safety of others, you must use the following normal shut-down 

procedure before leaving the tractor controls unattended for any reason, including servicing, cleaning, 

or inspecting the CMF-590.  A variation of the following procedure may be used if so instructed 

within this manual or your tractor manual or if an extreme emergency requires it.

1.  Disengage P.T.O.

2.  Place transmission in park or set park brake.

3.  Shut off machine and remove key.

4.  Wait for all movement to stop.

5.  Engage tractor park brake, turnoff and remove key engine prior to entering the tub and/or making any 

adjustments to CMF.

3.12  Light Kit

figure 3.8

Light kit for the CMF-590

Summary of Contents for HAYBUSTER CMF-590















































































































Reviews:

No comments