DuraTech Industries HAYBUSTER CMF-590 Operating Instructions And Parts Reference Download Page 19

Page: 19 / 110

C M F - 5 9 0

O P E R A T I N G I N S T R U C T I O N S

1.5 Safety review section

BEFORE OPERATING

•

Read and follow all instructions contained in:

This CMF-590 operator’s manual

Tractor operator’s manual

Decals on the CMF-590

Note:

Additional copies of the above mentioned materials can be obtained from your dealer.

•

Allow only responsible, properly instructed individuals to operate your machine. Provide proper training

and carefully supervise inexperienced operators.

•

Use a tractor which meets the tractor requirement contained within this manual. Additional weights may

be necessary.

•

Make sure all bystanders and other workers are clear before starting the tractor and CMF-590.

•

Make no modifications to the machine unless specifically recommended or requested by DuraTech

Industries.

•

Check periodically for breaks or unusual wear and make any necessary repairs.

•

Securely attach to towing unit. Use high strength, appropriately sized hitch pin with a mechanical

retainer.

•

If required install P.T.O. safety chain, check local regulations regarding safety chain requirements.

•

Be sure that there are no tools lying on or in the CMF-590.

•

Because it is possible that your CMF-590 may be used in dry areas or the presence of combustibles,

special precautions should be taken to prevent fires and fire fighting equipment should be readily

available.

•

Do not allow anyone to stand between the tongue or hitch and the towing vehicle when backing up to the

CMF-590.

Keep sufficient distance away from electrical power lines.

WARNING: Electrocution is possible when running this machine during an electric storm or heavy fog.

NO SMOKING IN THIS AREA

DANGER! NO OPEN FLAMES

IN THIS AREA

Summary of Contents for HAYBUSTER CMF-590















































































































Search results

Summary of Contents for HAYBUSTER CMF-590

Reviews:

DuraTech Industries HAYBUSTER CMF-590, Operating Instructions And Parts Reference, Page: 19 / 110

Search results

Summary of Contents for HAYBUSTER CMF-590

Reviews: