manualshive.com logo in svg

DuraTech Industries HAYBUSTER CMF-590, Operating Instructions And Parts Reference, Page: 35 / 110

Share
Download
DuraTech Industries HAYBUSTER CMF-590 Operating Instructions And Parts Reference Download Page 35

25

  C M F - 5 9 0    

O P E R A T I N G   I N S T R U C T I O N S

Section 4:  Lubrication

The operator should make a check of all grease fittings on the unit before beginning to operate it so as to become 

familiar with their location and correct service schedule.

Warning:

  Use normal shut-down procedure (Section 3.11) before lubricating the machine.

4.1 Lubrication

Use only a high quality, #2 multi‑purpose grease when lubricating the unit.  Make sure all fittings and the nozzle of the 

grease applicator are clean before applying the grease.  If grease fittings are missing, replace them immediately.

Lubricate with grease every ten (10) hours of operating time.

1.  P.T.O. universal joints – 8 places

 

1a.  

As many as seven (8) pumps of grease are required to purge all cross and  bearing lube    

 

 

point with fresh grease. 

2.  Telescoping shafts – 2 places

        2a.

 

 

Telescoping members require enough grease to maintain a smooth sliding

                     action.  When telescoping members become contaminated with dirty grease,

                     they should be inspected and cleaned to insure smooth operation.  

 

 2b.  

Shield components should be lubed and inspected to insure all components 

                     are in working condition or are replaced if damaged.  A properly maintained 

                     shield will inhibit dirt from contaminating telescoping members. 

3.  P.T.O stand bearing – 1

4.  Conveyor bearings - 2

5.  Extension conveyor bearings – 2 each

Lubricate with grease every fifty (50) hours of operating time.

6.

 

Automatic clutches – Two places – 1 pump only.  

Be careful not to over grease.

7. 

Auger grease line - 1

Summary of Contents for HAYBUSTER CMF-590















































































































Reviews:

No comments