manualshive.com logo in svg

DuraTech Industries HAYBUSTER CMF-590, Operating Instructions And Parts Reference, Page: 25 / 110

Share
Download
DuraTech Industries HAYBUSTER CMF-590 Operating Instructions And Parts Reference Download Page 25

15

  C M F - 5 9 0    

O P E R A T I N G   I N S T R U C T I O N S

When hooking up the machine, install a proper hitch pin and secure it with a hairpin clip or comparable device, crank 

the jack until the foot of the jack is fully raised.  Remove the jack pin and relocate the jack to the storage location.  

Reinstall the jack pin.

3.2.3 P.T.O. Shield

Warning: 

 Before lifting the P.T.O. shield be sure to follow the normal shut down procedure.  Be 

certain that the tractor is shut off and all rotating components of the machine have come to a complete 

stop before lifting shield.  Loose clothing is discouraged, and long hair should be restrained whenever 

working on P.T.O. shafts.

To raise the P.T.O. shield, remove the bolts from the front of the shield and lift the shield.  If it does not pivot freely 

look for build up of debris or other obstructions at the pivot point.  Do not force the shield, as damage to the shield may 

occur.

  

 

 

3.2.4 Hydraulic Cylinder and Valve

All cylinder and valve hose connections should be tight and leak free.  If the area near a hose connection becomes 

oily or dirty,  repairs should be made to seal the leak.  Hoses should be free of cracks or cuts to ensure safe operation.  

Cylinder seal kits are available from your dealer to repair a leaky cylinder.  Pin connections should be free of excessive 

wear.  If pins become worn they should be replaced.  Also check yokes and mounts for cracks and wear.

Warning: 

 Hydraulic fluid escaping under pressure can be almost invisible and can have sufficient 

force to penetrate the skin.  When searching for suspected leaks, use a piece of cardboard or wood 

rather than your hands.  If injured seek qualified medical attention immediately to prevent serious 

infection or reaction.

figure 3.2

Raising  the P.T.O. 

shield

CAUTION! NO STEP! DO 

NOT STEP OR STAND AT 

THIS LOCATION

PTO shield bolt

Summary of Contents for HAYBUSTER CMF-590















































































































Reviews:

No comments