DResearch TeleObserver MR3180 User Manual Download Page 52

Page: 52 / 66

DResearch – User Manual TeleObserver MR3180

2011-02-03

System event

Description

Alarm archives full

The unit’s archives are 100% full.

No more alarm data can be stored.

If necessary archive the data and then release the archive.

Alarm archives 80%
full

The unit’s archives are 80% full.

Alarm recording active

The recorder is recording alarm footage from one or more linked cameras.

Block lock active

The recorder’s block lock is activated.

Hard disk defect

The hard disk in the recorder is defective.

Data recording is no longer possible.

No hard disk found

No hard disk has been inserted into the recorder.

IBIS bus fault

IBIS signals are not being received.

Possible causes:

no available signal

signal cannot be read or other fault.

System ready for
operation

The recorder is ready for operation, i.e. it is connected to the power supply and has

completed the booting process.

Video signal from a
camera is missing

One of the cameras connected to the unit is not delivering a video signal.

GPS fault

GPS reception is disrupted.

Possible causes::

GPS aerial is faulty or not installed or there is no GPS reception (e.g. in a tunnel).

Camera sabotaged

One of the cameras connected to the unit has been sabotaged.

Alarm archives 60%
full

The unit’s archives are 60% full.

Unspecific system
failure

There is no miscellaneous system failure.

Summary of Contents for TeleObserver MR3180



































































Search results

Summary of Contents for TeleObserver MR3180

Reviews:

Related manuals for TeleObserver MR3180

Brands by name

Popular brands

DResearch TeleObserver MR3180, User Manual

Search results

Summary of Contents for TeleObserver MR3180

Reviews:

Related manuals for TeleObserver MR3180

Brands by name

Popular brands