Dover Markem Imaje 9040 User Manual Download Page 177

Page: 177 / 233

Alarms and faults

A36951-C.doc

178/236

During printing

Problems

Remedies

Phase detection on jet (number 1 to 4)

1a-

Clean and dry head electrodes.

1b-

Check general operating parameters for

printer.(

1c-

Check characteristics of ink used in the printer -

i.e. expiry date (refer to date shown on container),
ink change frequency and environment conditions
(see ink data sheet).

1d-

Run the REFRESHMENT function for two

minutes.

1e-

Check head electromagnetic environment

(possible interference).

1f-

The problem is on the main board. Contact

Markem-Imaje Technical Assistance.

Communication between the CPU and the

printer

2a-

The fault occurs while the message is being

printed, after the conveyor has been shut down for
an extended period. Print the message out again.

2b-

The fault persists after a message print test has

been performed at constant speed. The problem is
on the main board. Contact Markem-Imaje
Technical Assistance.

Print speed

3a-

Reset

Tacho Division

Print speed

parameter settings on the printer.

Summary of Contents for Markem Imaje 9040










































































































































































































































Search results

Summary of Contents for Markem Imaje 9040

Reviews:

Related manuals for Markem Imaje 9040

Brands by name

Popular brands

Dover Markem Imaje 9040, User Manual

Search results

Summary of Contents for Markem Imaje 9040

Reviews:

Related manuals for Markem Imaje 9040

Brands by name

Popular brands