Dover Markem Imaje 9040 User Manual Download Page 88

Page: 88 / 233

Editing a message

A36951-C.doc

89/236

Example:

Start time : 06 : 00

Interval

: 08 : 00

Type

: LETTER

The printer will print:

A - 06.00 to 13.59,

B - 14.00 to 21.59,

C - 22.00 to 05.59 the next day and so on.

Default parameter values

The default parameters are common to all messages and are configured in the

Printer preparation/Parameters/

Shift code

The dialog box is identical.

Insert shift code

Message editing/Variables

/Shift code

This function is for inserting a shift code in your message. An alphabetic or numerical
character is displayed in the message at the cursor location, based on your parameters.

Summary of Contents for Markem Imaje 9040










































































































































































































































Search results

Summary of Contents for Markem Imaje 9040

Reviews:

Brands by name

Popular brands

Dover Markem Imaje 9040, User Manual

Search results

Summary of Contents for Markem Imaje 9040

Reviews:

Brands by name

Popular brands