Dover Markem Imaje 9040 User Manual Download Page 86

Page: 86 / 233

Editing a message

A36951-C.doc

87/236

Datamatrix code

The code used is type ECC200 and the format is calculated automatically

(square or rectangle).

Cell size (stretch) is programmable: 1 or 2 drops.

The code height can vary between:

8 and 24 cells in stretch mode 1

8 and 12 cells in stretch mode 2

All types of variables can be printed with the code.

Maximum code capacity

Code height

(number of cells)

Code width

(number of cells)

Number of coded numeric

characters

Number of coded

alphanumeric characters

Number of coded 8-bit

ASCII characters

Stretch 1

Printed code height

(number of drops)

Printed code width

(number of drops)

Stretch 2

Printed code height

(number of drops)

Printed code width

(number of drops)

CAUTION

The resolution of the message will be determined by the
datamatrix code resolution value.
In some cases, it may be necessary to increase the
head/object distance to avoid superimposing drops.
This will make it possible to read the code.

Summary of Contents for Markem Imaje 9040










































































































































































































































Search results

Summary of Contents for Markem Imaje 9040

Reviews:

Brands by name

Popular brands

Dover Markem Imaje 9040, User Manual

Search results

Summary of Contents for Markem Imaje 9040

Reviews:

Brands by name

Popular brands