Dover Markem Imaje 9040 User Manual Download Page 113

Page: 113 / 233

Servicing: 9040, 9040 IP65, 9040S

A36951-C.doc

114/236

Start-up following a prolonged shutdown

Starting the printer after a shutdown lasting 8 to 15 days

Open gutter located in the print head

Start the printer.

Perform a STABILITY check, if necessary

Perform a five-minute ink REFRESHMENT

routine.

Starting the printer after a shutdown lasting 15 days or longer.

This operation consists of three stages:

. Drain the ink circuit

Refer to Drain ink circuit procedure contained in this section.

. Change the main ink filter cartridge.

Refer to "Change ink filter cartridge for 9040, 9040 IP and 9040S printers" procedure
contained in the Maintenance section of this manual.

. Reintroduce new ink to the printer.

Refer to Re-introduce ink procedure contained in this section.

Summary of Contents for Markem Imaje 9040










































































































































































































































Search results

Summary of Contents for Markem Imaje 9040

Reviews:

Related manuals for Markem Imaje 9040

Brands by name

Popular brands

Dover Markem Imaje 9040, User Manual

Search results

Summary of Contents for Markem Imaje 9040

Reviews:

Related manuals for Markem Imaje 9040

Brands by name

Popular brands