manualshive.com logo in svg

Dover Markem Imaje 9040, User Manual

Share
Download
Dover Markem Imaje 9040 User Manual Download Page 48

Daily operation 

A36951-C.doc

49/236 

Ŷ

 Print a message 

1.

 Ensure jet(s)are ready: the 

 light is on continuously. 

2.

 The message or messages to be printed are ready (in production). 

3.

 The cell or cells on the TOP1/TOP2 input or the tachometer on the Tacho input sends a 

signal to the printer to trigger the printing operation.  

The printer prints the message in production. 

Stop/Restart printing 

Press

 and confirm using 

 to stop the current print job. 

Press

 and confirm using 

 to restart printing.  

Load printer 

1.

 Press 

in Message editing mode to save and load the message.

(

Message editing/Message/ 

Load printer)

2.

 On a two-head printer, you may need to select the head to be assigned the message 

and then press 

ҏҏ

 to confirm

The message is ready to be printed 

Summary of Contents for Markem Imaje 9040










































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands