Dover Markem Imaje 9040 User Manual Download Page 216

Page: 216 / 233

Technical Specifications

A36951-C.doc

217/236

°C

Physical characteristics

Dimensions

Control cabinet: 927.19 mm X 460 mm X 389.25 mm (36.504" X 18.11" X 15.325")

Single jet and two-jet printhead: 225 mm X 44.5 mm X 47.5 mm (8.8" X 1.7" X 1.9")

Weight

Control cabinet: 40 kg (88.2 lbs)

Head/umbilical assembly: 3 kg (6.6 lbs)

Capacities

Tanks :

Total volume: 2 liters (3.52 pints) - Working : 1 liter (1.76 pints)

Installation details

Working position

Control cabinet: vertical

Printhead: vertical or horizontal

Maximum height differential between head and control cabinet

± 2 meters (± 6.56 ft)

Distance between head and control cabinet

3 meters (9.8 ft), 5 m (16.4 ft) and 8 m (26.2 ft) depending on type of machine and options.

Head-object distance

G head: 10 mm (0.39") or 30 mm (1.18") depending on font used

M head: 8 mm (0.32") or 20 mm (0.79") depending on font used

P head: 6 mm (0.24")

Power supply

Electricity

100 V - 240 V AC - Frequency: 50 to 60 Hz

Consumption: Depends on model (see manufacturer's nameplate at the back of the
printer)

Compressed air

Pressure: 5 to 8 bar (72 to 116 psi)

Summary of Contents for Markem Imaje 9040










































































































































































































































Search results

Summary of Contents for Markem Imaje 9040

Reviews:

Related manuals for Markem Imaje 9040

Brands by name

Popular brands

Dover Markem Imaje 9040, User Manual

Search results

Summary of Contents for Markem Imaje 9040

Reviews:

Related manuals for Markem Imaje 9040

Brands by name

Popular brands