background image

DPM-OTR  

Version 1 

2019-01-28 

16

IV. ALARM MODES 

NOTE: 

 Alerts indicate that the vehicle is being operated in a dangerous condition. 

When an alarm is triggered, STOP and check the tire(s) as soon as safely 

possible and investigate. The warning will continue to be reported as long 
as the malfunction exists.   

 

NOTE:         When an alarm occurs, the audible alarm will sound. Pressing any button will 

silence the audible alarm but will not clear it (Audible alarm is not available 

on the “black box” products).  

 

The DORAN 360OTR has five types of alarm modes. The warning levels are: 

 

Under Pressure – Tire pressure is 12.5% or more below the programmed baseline 

air pressure. 

o

 

When  an  Under  Pressure  alarm  is  reported,  the  backlight  of  the  monitor 

screen will illuminate. The Green Means Good™ indicator light will turn off, the 

red warning LED will begin to flash, and the audible alarm will sound at a rate 

of one flash/beep per second. The tire position 

with the alarm condition will be highlighted, the 

current  pressure  reading  displayed,  and  the 

words “LOW PRESSURE” will be displayed on 

the monitor (See Figure 4-1) 

 

Extreme Under Pressure – Tire pressure is 25% or more below the programmed 

baseline air pressure. 

o

 

The National Highway and Traffic Safety Administration considers a tire flat 

when  the  pressure  is  25%  below  the  tire  manufacturers’  recommended 

operating pressure 

o

 

When  an  Extreme  Under  Pressure  alarm  is  reported,  the  backlight  of  the 

monitor  screen  will  illuminate.  The  Green  Means  Good™  indicator  light  will 

turn off, the red warning LED will begin to flash, and the audible alarm will 

sound at a rate of two flashes/beeps per second. The tire position with the 

alarm condition will be highlighted, the low pressure displayed, and the words 

“LOW PRESSURE” will be displayed on the monitor (See Figure 4-1). 

Figure 4-1 

Summary of Contents for 360OTR




























Reviews: