Domo Sapphire RXD3 Setup Manual Download Page 12 | Manualshive

Page: 12 / 43

Domo Sapphire RXD3 Setup Manual Download Page 12

Revision: 1.0

Sapphire-RXD3 Setup Guide

Copyright © 2022 Domo Tactical Communications (DTC) Limited. All rights reserved.

Commercial in Confidence

Page 4-7

4. Front Panel Touchscreen Control

4.1 Power

The Sapphire-RXD3 requires 12VDC power which can be supplied via the supplied mains PSU. There

is a power switch on the front panel which can be used to power On/Off the unit.
When the unit has been switched on, it will take approximately 90s to boot-up.

4.2 Introduction

The Sapphire-RXD3 has a front panel touchscreen which can be used to monitor and control the

device without the need to connect to a PC device.
When the unit has fully booted, the front panel touchscreen will display the home screen and the

power LED will be illuminated.
Press the lock symbol, indicated below, for 5 seconds to lock the screen, if required.

The home screen will show colour-coded information and is divided into two zones,

Left

and

Right

.

«
...
10
11
12
13
14
...
»

Summary of Contents for Sapphire RXD3












































Reviews:

No comments