DIY BBQ Angela 'L' Island Instruction Manual Download Page 40

Page: 40 / 48

Place the precut Appliance Tracks in-between the Countertop Studs, one near the back of the module, one near the

front. Make sure that the smooth side of the Appliance Tracks face inward, toward the appliance.

Note: The Appliance Tracks have been precut to fit the width of the appliance. To best position the appliance,

place one side of the Appliance Track flush against the first Countertop Stud, then readjust the second Countertop

Stud to rest flush against the other end of the Appliance Track.

Step

Measure the distance between the Appliance Tracks to make sure it matches the depth of the appliance that will

be placed within this area. If the size is incorrect, slide the Appliance Tracks forward or back along the Countertop

Studs until the size between the Appliance Tracks and the placement of the appliance are correct and to your liking.

Note: Add an eighth or a quarter of an inch to the size of your appliance to make sure the appliance slides in

easily.

Step

Smooth side

toward the

appliance

Open side

away from

the appliance

Length between the smooth sides of

the Appliance Tracks will equal the

depth of the appliance.

Summary of Contents for Angela 'L' Island
















































Search results

Summary of Contents for Angela 'L' Island

Reviews:

Related manuals for Angela 'L' Island

Brands by name

Popular brands

DIY BBQ Angela 'L' Island, Instruction Manual

Search results

Summary of Contents for Angela 'L' Island

Reviews:

Related manuals for Angela 'L' Island

Brands by name

Popular brands