DIY BBQ Angela 'L' Island Instruction Manual Download Page 39 | Manualshive

Page: 39 / 48

background image

39

Drop-In Only Cutout (Sink)

Step

1

1

Clamp the Short Catch Tracks to the back and front Perimeter Wall Tracks of your module with Vice Clamps

about where you would like to place your appliance. Make sure that the top of the Short Catch Tracks is flush with

the top of the Perimeter Wall Tracks.

Place the Countertop Studs perpendicular to the Short Catch Tracks and center them within the Catch Tracks.

Note: Make sure the smooth sides of the Countertop Studs are facing the appliance.

2

2

Step

Smooth side

toward the

appliance

Open side

away from

the appliance

«
...
37
38
39
40
41
...
»

Summary of Contents for Angela 'L' Island

















































Reviews:

No comments

Related manuals for Angela 'L' Island

Brand: IGF Pages: 32

Brand: Makita Pages: 44

Brand: Napoleon Pages: 50

Brand: Bort Pages: 28

Brand: Bull Pages: 25

Classic LXS 3 Series

Brand: Campingaz Pages: 136

Brand: Camp Chef Pages: 2

VC0620P, VC0680P, VC0680N

Brand: Vermont Castings Pages: 40

Brand: Masterbuilt Pages: 8

Brand: EINHELL Pages: 42

Brand: Gallet Pages: 44

Brand: WT Pages: 14

Brand: Happy Garden Pages: 7

Brand: Blue Seal Pages: 17

Brand: Hitachi Pages: 58

Brand: Surtek Pages: 16

Brand: Jet Pages: 8

Brand: Jet Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands