DIY BBQ Angela 'L' Island Instruction Manual Download Page 47

Page: 47 / 48

Step

Measure the length of the Long Catch Track to the length of the Perimeter Wall Track of your module and mark

the Stud. When measuring the length of the Perimeter Wall Track of your module, make sure to measure between

the inner sides of the Cross Channel Tracks.

Note: The size of the Long Catch Track doesn’t have to match the length of the Perimeter Wall Track exactly.

Fully cut the end of the Long Catch Track and discard the excess piece.

Note: It is much easier to cut the track with a cutoff wheel, however, if you are not comfortable with using the

cutoff wheel, aviation snips will work as well. (See inset)

Use the carpenter square to draw a straight line across the entirety of the top of the Long Catch Track where

marked in step 1.

Step

Discard

You now have a correctly sized Catch Track.

Cutting Long Catch Tracks

Summary of Contents for Angela 'L' Island
















































Search results

Summary of Contents for Angela 'L' Island

Reviews:

Related manuals for Angela 'L' Island

Brands by name

Popular brands

DIY BBQ Angela 'L' Island, Instruction Manual

Search results

Summary of Contents for Angela 'L' Island

Reviews:

Related manuals for Angela 'L' Island

Brands by name

Popular brands