DIY BBQ Angela 'L' Island Instruction Manual Download Page 24

Page: 24 / 48

Place the second Appliance Track between the Perimeter Wall Studs by inserting it at an angle and then sliding it

into position. Make sure that the smooth side of the Appliance Track is facing up, toward the appliance.

Step

Measure the position of the second Appliance Track so that it matches the height of your appliance. If it does not

match the height of your appliance, move the Appliance Track up or down along the Perimeter Wall Studs until it

matches the height of your appliance.

Note: Before measuring, consider the width of any countertop and/or cement board you may use to decorate your

module. For example, if you will be using 2” countertop and .5” cement board, the Appliance Track must be raised

2.5” to accommodate this extra height.

Step

Smooth side

toward the

appliance

Slide Up

Open side

away from

the appliance

Length between the top of the Perimeter

Wall Track and the Appliance Track will

equal the height of the appliance.

Summary of Contents for Angela 'L' Island
















































Search results

Summary of Contents for Angela 'L' Island

Reviews:

Related manuals for Angela 'L' Island

Brands by name

Popular brands

DIY BBQ Angela 'L' Island, Instruction Manual

Search results

Summary of Contents for Angela 'L' Island

Reviews:

Related manuals for Angela 'L' Island

Brands by name

Popular brands