DIY BBQ Angela 'L' Island Instruction Manual Download Page 26

Page: 26 / 48

Double Doors Cutout

Step

Place the first Appliance Track in-between the Front wall studs near the bottom of the Appliance Track used for the

Slide-In and Drop Cutout by inserting it at an angle and then sliding it into position to align parrallel with the above

Appliance Track. The Appliance Track has been precut to fit the width of the Doors, which should match the width

of the Grill.

Note: Make sure that the smooth side of the Appliance Track is facing down, toward the Double Doors.

Smooth side

toward the

Double Doors

Slide Up

Open side

away from

Double

Doors

Place the second precut Appliance Track between the Perimeter Wall Studs by inserting it at an angle and then

sliding it into position at the bottom of the module. Make sure that the smooth side of the Appliance Track is facing

up, toward the Double Doors.

Step

Slide

Down

Open side away

from Double

Doors

Smooth side

toward the

Double Doors

Summary of Contents for Angela 'L' Island
















































Search results

Summary of Contents for Angela 'L' Island

Reviews:

Related manuals for Angela 'L' Island

Brands by name

Popular brands

DIY BBQ Angela 'L' Island, Instruction Manual

Search results

Summary of Contents for Angela 'L' Island

Reviews:

Related manuals for Angela 'L' Island

Brands by name

Popular brands