Vermont Castings VCS3008B Series, VCS3008BI Series, VCS4008 Series, VCS5008 Series, VCS5008I Assembly Procedures Download Page 1

Page: 1 / 12

Assembly Procedures

VCS3008BI Series / VCS5008BI Series

Tools Required:

Knife or scissors, Phillips or Robertson (square head) screwdriver.

CAUTION: This grill is intended ONLY to be built into an enclosure.
CAUTION: The assembly of this grill requires two (2) people.
WARNING: Some parts may have sharp edges; to avoid injury, wearing gloves during assembly,
lifting or moving the grill is recommended. Protective eyewear and long sleeves are also strongly
recommended.
NOTE:

Remove the protective plastic coating from the stainless steel, failure to do so will void the warranty.

50004808 1/08 Rev. 3 En

��
��
��

Summary of Contents for VCS3008B Series, VCS3008BI Series, VCS4008 Series, VCS5008 Series, VCS5008I













Search results

Summary of Contents for VCS3008B Series, VCS3008BI Series, VCS4008 Series, VCS5008 Series, VCS5008I

Reviews:

Related manuals for VCS3008B Series, VCS3008BI Series, VCS4008 Series, VCS5008 Series, VCS5008I

Brands by name

Popular brands

Vermont Castings VCS3008B Series, VCS3008BI Series, VCS4008 Series, VCS5008 Series, VCS5008I, Assembly Procedures

Search results

Summary of Contents for VCS3008B Series, VCS3008BI Series, VCS4008 Series, VCS5008 Series, VCS5008I

Reviews:

Related manuals for VCS3008B Series, VCS3008BI Series, VCS4008 Series, VCS5008 Series, VCS5008I

Brands by name

Popular brands