SBH-E
:
REV
A
DiBO
n.v.
125
6.3 Description daily control
6.3.1. Frame
Check the frame in its entirety at loose bolts and/or cracks of the welds.
Keep the machine as much as possible clean to prevent act on dirt, water, oil and messed fuel.
6.3.2. manometer
$WDQVZLWFKHGRIIPDFKLQHWKLVPHDQVDKDOWHGHQJLQHWKHPDQRPHWHUPXVWUHÀHFWEDU
At an maximum performing machine, this means operated at full load working engine, the manometer can
not indicate more than the maximum pressure by DiBO indicated, for your machine.
After operation and releasing the gun can still remain a small pressure remainder present.
7KHUHÀHFWHGYDOXHRIWKHPDQRPHWHUPXVWEHEHWZHHQEDUWKHYDOYHVDUHWKHQDOOULJKW
6.3.3. High pressure pump
Check the pump on loose connections, bolts, seals and leaks.
Check regularly the oil level of the pump.
If the oil level has decreased too much or pollution of oil is observed, should these be replaced before work-
ing further. Puts the machine on a horizontal base. The oil level must stand halfway the level glass.
Take at doubt the oil level stick separately, where the oil level must stand between both mark lines.
If pump oil gives a milky impression, frequently indicates this on an internal leak as a result of which water
touched oil there.
Immediately repair
is necessary then.
6.3.4. High pressure- and low pressure parts
Check the hoses, piping and connections on external damages and leaks.
If damaged or leaks these must be immediately replaced.
6.3.5. Spray tools
Check lances and guns on leaks, external damages and hair cracks.
If damaged or leaks these must be immediately replaced.
Check the spray image of the water jet, if these blows out to much you must replace the nozzle.
Check protective cap-nozzle on damages and replace if necessary.
Check the thread of the couplings on external damages. At damage let these replace without delay.
6.3.6. Electrical part
Checks visible electric wiring and components (among other things switches) on external visible damages.
If damaged let replace the concerning parts.
6.3.7. Control box
Check the good functioning of the push buttons, the coin selector and the screen.
6.3.8. Water tank
Check the water tank on external damages and leaks.
&KHFNZKHQWKHWDQNLV¿OOLQJLIWKHÀRDWV\VWHPZRUNVSURSHUO\
6.3.9. Oil drainage HP- pump
Put a oil trough under the drain plug.
Remove the drain plug. Let all the oil in the oil trough.
Assemble the drain plug (with a new packing ring).
2LO¿OOLQJ+3SXPS
Remove the oil-level gauge. Flll the engine crankcase with oil until the oil-level comes up to the middle of
the gauge (type oil see technical data). Check the oil-level on the basis of the marks on the oil-level gauge.
Place back the oil- level gauge.
6.3.11. Carry away used oil
Pour the tapped oil in a can. Deliver the tapped oil by your dealership or at the proper authorities.
Summary of Contents for SBH-E
