manualshive.com logo in svg

Diamond SmartLyte Plus, Service Manual

Share
Download
Diamond SmartLyte Plus Service Manual Download Page 5

Table of Contents

 

ECO 9099 SOP05-5090F Rev.00 Effective Date: 12/20/18  Page 5 of 58 

 

 

1.

 

Introduction

 ................................................................................................................................................. 7

 

1.1.

 

General Description

 ............................................................................................................................ 8

 

1.1.1.

 

Measurement

 .................................................................................................................................. 8

 

1.1.2.

 

Operating Configurations

 .............................................................................................................. 8

 

1.2.

 

Software Operation

 ........................................................................................................................... 10

 

1.3.

 

Description of Modules

 .................................................................................................................... 11

 

1.3.1.

 

Mechanical Assemblies

 ............................................................................................................... 11

 

1.3.1.1.

 

Front Door Assembly

 ............................................................................................................... 11

 

1.3.1.2.

 

Rear Panel Subassembly

 ........................................................................................................ 14

 

1.3.1.3.

 

Power Supply Subassembly

 ................................................................................................... 15

 

1.3.1.4.

 

Power Inlet Module Subassembly

 ......................................................................................... 16

 

1.3.1.5.

 

CPU Board (CN-A4405)

 .......................................................................................................... 17

 

1.3.1.6.

 

Aspiration Assembly

 ................................................................................................................. 21

 

1.3.1.7.

 

Electrode Tray Assembly

 ........................................................................................................ 26

 

1.3.1.8.

 

Peristaltic Pump Rotor (CN-A4014)

 ....................................................................................... 29

 

1.3.1.9.

 

Peristaltic Pump Motor

 ............................................................................................................. 30

 

1.3.1.10.

 

Solenoid Valve System

 ........................................................................................................ 31

 

1.3.1.11.

 

Printer Assembly (CN-A4060)

............................................................................................. 34

 

1.3.1.12.

 

RFID Board (CN-A4054)

 ...................................................................................................... 36

 

1.3.1.13.

 

Valve Board (CN-A4018)

 ..................................................................................................... 36

 

1.3.1.14.

 

Display Board (CN-A4406)

 .................................................................................................. 38

 

1.3.1.15.

 

Interface PC

 ........................................................................................................................... 39

 

1.4.

 

Fluidic Modules

 .................................................................................................................................. 40

 

1.4.1.

 

Standard A

..................................................................................................................................... 40

 

1.4.2.

 

Standard B and C

 ......................................................................................................................... 40

 

1.4.3.

 

Reference Solution

 ...................................................................................................................... 40

 

1.4.4.

 

Waste Liquids

 ............................................................................................................................... 40

 

1.4.5.

 

Fluidic Flow Path

 .......................................................................................................................... 41

 

1.4.6.

 

Pinch Valve Tubing Set (AV-BP5193)

 ...................................................................................... 42

 

1.4.7.

 

Fluidic Diagram

 ............................................................................................................................. 45

 

1.5.

 

Electronics

 .......................................................................................................................................... 46

 

1.5.1.

 

Block Diagram of SmartLyte® Plus

 ........................................................................................... 46

 

1.5.2.

 

CPU Board

 .................................................................................................................................... 46

 

1.5.3.

 

Power Circuits

 ............................................................................................................................... 48

 

1.5.4.

 

Microcontroller

 .............................................................................................................................. 48

 

1.5.5.

 

EMF and Noise Shielding

 ........................................................................................................... 48

 

1.5.6.

 

Fluid Pack Sensor

 ........................................................................................................................ 48

 

1.5.7.

 

Valve Drivers

 ................................................................................................................................. 49

 

1.5.8.

 

Pump Motor Driver

 ....................................................................................................................... 49

 

1.5.9.

 

Input Amplifiers

 ............................................................................................................................. 49

 

1.5.10.

 

Temperature Sensor circuit

 ..................................................................................................... 49

 

1.5.11.

 

Analog Channel and A/D Converter

 ...................................................................................... 49

 

1.5.12.

 

CPU board Connector

 ............................................................................................................. 49

 

1.5.13.

 

Valve Board

 ............................................................................................................................... 49

 

1.5.14.

 

Display Board

 ............................................................................................................................ 50

 

1.5.15.

 

Printer

 ......................................................................................................................................... 50

 

1.5.16.

 

Shielding and Grounding

 ......................................................................................................... 50

 

1.5.17.

 

Interface PC

 ............................................................................................................................... 50

 

2.

 

Scheduled Maintenance

 ......................................................................................................................... 51

 

Summary of Contents for SmartLyte Plus



























































Reviews:

No comments

Brands by name

Popular brands

Load more brands