manualshive.com logo in svg

Diamond SmartLyte Plus, Service Manual

Share
Download
Diamond SmartLyte Plus Service Manual Download Page 50

1 Introduction

 

ECO 9099 SOP05-5090F Rev.00 Effective Date: 12/20/18  Page 50 of 58 

 

 

1.5.14.  Display Board  

The display board is comprised of 2 stacked boards. The 1st board has the 5” touch screen 
display mounted on it. This display is then connected to display adaptor board that gets 
power from CPU board and HDMI signals from interface PC. Touch signals are sent back to 
the interface PC via flex ribbon cable.  
 
Additionally, the display adaptor board has one RJ11female connector mounted on it. Sample 
sensor male RJ11 connector from electrode tray plugs to RJ11 female connector. 

1.5.15.  Printer  

The printer is a graphics printer with 192 dots of a TP series.  

1.5.16.  Shielding and Grounding  

Beside the shield for eliminating the internal noise from the power supply, the entire 
SmartLyte

®

 Plus is equipped with a protective shield to prevent the influence of magnetic 

fields, and other noise sources in the laboratory. The internal protective shield creates a 
“

Faraday Cage

” that protects instrument measurements from outside noise. This shield is 

also grounded with a grounding wire in the power receptacle in the power switch input. 

1.5.17.  Interface PC 

SmartLyte

®

 Plus has an interface PC which has pre-installed Linux OS installed on it. This Interface-

PC is responsible for following peripherals/features: 

•

  Graphic User Interface 

•

  Display 

•

  Touch Screen 

•

  LAN/Wi-Fi connection 

•

  Network LIS 

•

  Auto updates 

•

  Data storage 

•

  USB (x4) 

 

Summary of Contents for SmartLyte Plus



























































Reviews:

No comments

Brands by name

Popular brands

Load more brands