manualshive.com logo in svg

Diamond SmartLyte Plus, Service Manual

Share
Download
Diamond SmartLyte Plus Service Manual Download Page 42

1 Introduction

 

ECO 9099 SOP05-5090F Rev.00 Effective Date: 12/20/18  Page 42 of 58 

 

1.4.6.  Pinch Valve Tubing Set (AV-BP5193) 

The pinch valve tubing set contains all tubing required for the analyzer. The tubing set has a pre-

cut tubing, a  harness with fluidic interconnections preassembled. The Peristaltic Pump Tubing, 

AV-BP5027D

, is also included in the set. (

Figure 1-60

) 

 

Figure 1-60 Pinch Valve Tubing Set Diagram 

Replacement of the tube set should be performed annually. Follow the procedure below; 

1.  Place the instrument in Hold in Maintenance mode to prevent reagents from cycling.  

(Main Operations Menu>>>Maintenance>>>Hold in Maintenance) 

2.  Remove the Fluid Pack from the reagent compartment.  

3.  Next, follow the procedure outlined in 

Section 1.3.1.10

 to remove the indicator cap and crimp 

pin from each solenoid valve. This facilitates the removal of tubing from each solenoid. 

4.  Pull the two pump tubes of the peristaltic pump tube set off the pump rotor. 

5.  Unplug the reference from the connector. Use a towel to absorb any reference solution that 

leaks from the housing  

6.  Pull out the white reference solution tube connector.  

7.  Gasp the front of the white TPR block and slide it out of the analyzer towards you. 

8.  Disconnect the green tagged tube from the electrode tray and the red tagged tube from the 

bottom of the fill port.  

9.  Remove and discard all tubes. 

10. Remove parts from the tubing kit which include the tubing harness, green tagged waste tube 

and Peristaltic Pump Tubing separately. 

11. Connect the green tagged tube to the electrode tray as shown in 

Figure 1-62

. 

 Waste Out 

< --Waste In 

Reference Out

 

↑

 

Reference 

In 

Summary of Contents for SmartLyte Plus



























































Reviews:

No comments

Brands by name

Popular brands

Load more brands